-
Recent Posts
Archives
- September 2024
- July 2022
- April 2022
- July 2021
- May 2021
- December 2020
- October 2020
- June 2020
- May 2020
- November 2017
- September 2017
- April 2017
- July 2016
- June 2016
- May 2016
- March 2016
- February 2016
- December 2015
- November 2015
- August 2015
- July 2015
- October 2014
- February 2014
- January 2014
- December 2013
- November 2013
- October 2013
- July 2012
- June 2011
- May 2011
- December 2010
- November 2010
Tags
Blogroll
Author Archives: rob
Jeep LJ No Drill Safari-Style Bikini Header. Making it work!
I bought a Besttop “No Drill” safari-style bikini header for my 2006 Jeep Wrangler LJ. The online forums have mixed opinions about ease of installation or re-installation. If I had read that thread first, I might have purchased the drill … Continue reading
SWR measurements of a SOTABeams Band Hopper
I am not yet a SOTA/POTA activator, though I would like to be (actually, I have one SOTA activation on 2m VHF). However, I do travel with my radio, and have brought my Kx3 on trips, along with a 20m … Continue reading
Posted in Uncategorized
Leave a comment
IKEA couch spring repair
About a year ago we purchased and assembled an IKEA sectional sofa for our living space. A few months later, we notice one of the springs under one of the cushions had sprung loose. And another. By nearly a year … Continue reading
Posted in Uncategorized
Leave a comment
Scout’s vigil and the beginning of the aftermath
Note: A friend asked if I’d share this FB post more widely. I refuse to make it global on FB, as it would then invite the inevitable cesspool of comments if it was shared widely. But feel free to link … Continue reading
Posted in Uncategorized
Leave a comment
RFID-activated High-Current Power Supply Switch
More details forthcoming. Notes: 2N3904 transistors were replaced by ones with a much lower VCE voltage. The 220uF decoupling capacitor is critical to avoid odd slow powerup oscillations (likely due to relay inductance). Schematic at EasyEDA PDF schematic The enclosure … Continue reading
Posted in Uncategorized
Leave a comment
Backslash line continuation in code comments
I spent several hours this weekend tracking down a bug that highlights something I never knew about GCC (and the Arduino IDE, which uses GCC). At first I was inclined to blame the limited Arduino IDE, but that in itself … Continue reading
Arduino Class Sunday July 24 2016
This is a reference post for the Intro Arduino class I am teaching at Decatur Makers on July 24, 2016, from 6pm-9pm. See the Decatur Makers website for cost and registration info. Getting Started with the Arduino! Low-cost user-friendly microcontrollers … Continue reading
Posted in Uncategorized
Leave a comment
Tontec 480×320 touchscreen display with Raspberry Pi
Last December, I purchased a Tontec 480×320 touchscreen display for use with a Raspberry Pi. Complete with case (amazon link). I bought it along with a Raspberry Pi Model B in order to play with software-defined radio (SDR), motivated by … Continue reading
Serial communication with a Kenwood TS-570D
I am setting up an amateur radio station at my local maker space, Decatur Makers. Our transceiver is a Kenwood TS-570D. I have spent a lot of time debugging how to get serial communications working between the Kenwood and a … Continue reading
KX3 as a (good enough) antenna analyzer
So I am working on a DIY antenna analyzer/impedance meter. But I need to validate my design against a known antenna analyzer. I do not own one. But I do — my Elecraft KX3 can calculate SWR. If you know … Continue reading